Dodge Journey Alarm Going Off? (12 Simple Causes)

The Dodge Journey is an affordable midsize SUV that was produced for the U.S. market for the 2009 to 2020 model years. 

As is the case with most vehicles, this model is prone to alarm-related problems. 

If your Journey’s alarm system keeps going off, this article should have the details you need!

Why Does My Dodge Journey Alarm Keep Going Off?

A Dodge Journey alarm is usually triggered by a faulty door switch or hood switch as these sensors are prone to defects or damage through years of use. Other common causes include an overly sensitive ultrasonic alarm sensor, battery issues, and damaged wiring. 

1. Faulty Door Switches

Faulty door switches (including the rear hatch) are a common cause of random alarms. If damaged, faulty, or dirty, they can send false readings thereby triggering the alarm.

Door switches are a common point of failure as they are subject to wear and tear due to the doors being continually opened/closed/slammed etc.

The door latches and door switches can get dirty too which can cause issues, so the first thing you should do is give all door latches a good clean and spray some WD-40 on the latch and work it in to see if that helps.

Also check the wiring leading from the body into the door for any signs of damage, it should be in a flexible hose on the hinge side of the door.

If you suspect the alarm issues are linked to the door switch, ask your dealer to run a diagnostic test to try and pinpoint the fault.

This was what one owner had to say on the r/MechanicAdvice subreddit:

“You probably have a bad door switch, tailgate switch, or a broken wire in the driver’s door. If the body module sees a door open the alarm will sound.”

2. Faulty Hood Switch

A faulty hood switch is a common cause of unwanted alarms for this type of vehicle.

The switch is typically embedded in the hood latch.

The small electronic device is designed to detect whether the hood is open or shut and is an important part of the car’s alarm system – if it is broken, loose or dirty it can send false readings to the car’s computer thus triggering the alarm.

  • Pop the hood and locate the hood switch.
  • Check for any obvious damage, rust or loose connections.
  • Give the hood switch a clean too (use contact cleaner), as dirt and grime can cause issues.
  • You can test the switch with a continuity tester.

If you are well-versed mechanically, you can buy a new hood switch online and replace it yourself. Otherwise, we’d advise visiting your local mechanic.

We found this comment on the r/cars subreddit:

“Lock the car and press down and lift up on the hood. If the alarm goes off then your hood switch may be faulty or your hood may be out of adjustment. Random alarms are often caused by bad hood switches.”

3. Loose or Bad 12V Battery Connections

Loose or bad 12V battery connections can cause a number of problems, including triggering the alarm of your vehicle.

A bad connection can be caused by dirt or gunk buildup.

The terminals may have come loose from driving and vibrations etc.

Make sure the engine is off before doing any work on the battery.

  1. Inspect the battery and look for any signs of damage, dirt build-up, rust, or corrosion.
  2. Disconnect the battery and loosen the nuts on the clamps using a wrench.
  3. Remove the negative clamp, marked with a – symbol first.
  4. Clean the terminals with a toothbrush dipped in a mix of baking soda and water, rinse with distilled water and dry with a cloth.
  5. Reconnect the battery, ensuring tight connections.

One owner suggested this on the r/cars subreddit:

“It may be time for a new battery in the Journey.”

We also found this on DodgeJourneyForum.com:

“Try disconnecting the battery for a bit.”

4. Drained 12V Battery

A faulty or weakened car battery causes a variety of problems, including accidentally triggering the alarm.

The best thing to do is take your unit for a battery health check, these are usually quite inexpensive or sometimes free such as at AutoZone.

Or you can test it yourself with a multimeter (see the guide at the end of this article).

A healthy 12V battery should be about 12.6 to 12.8 volts while a weakened battery reads below 12 volts.

5. Key Fob Running on Low Battery

A common cause of mysterious alarms is a low key fob battery. Similarly, if the fob is dirty or dusty this can also cause alarm issues.

Give the inside of your fob a clean and replace the battery to eliminate this possible cause. It’s worth spending a bit extra for a good brand of battery.

  • To open your key fob, stick your prying tool into the slit or gap between the two halves of the outer casing and gently apply upward pressure to pop open the device.
  • Remove the battery.
  • Give the key fob a good clean to remove any dirt or fluff – a cotton swab and some rubbing alcohol should do the trick.
  • Check for damage, rust or loose connection (you may need a new key fob depending on what you find).
  • Be sure to insert the new battery facing the right way up.
  • Assemble the outer casing of your key fob by clamping them back together.

6. Faulty Key Fob

Another reported cause of nuisance alarms on this vehicle is a faulty key fob.

If you have 2 remotes, try taking the battery out of one and use the other for a while.

If the alarm problems persist, and you have tried cleaning the inside of the fob(s) and changing the battery, the best thing to do is speak with your dealer.

7. Overly Sensitive Ultrasonic Alarm

It has been frequently reported online that there have been recurring issues with the ultrasonic alarm system of this model, often inadvertently setting the alarm.

Dealers recommend disabling the ultrasonic sensors to prevent erroneous alarms from happening. 

“They said there was an issue with these alarms and Chrysler Technical are dealing with it. In the meantime they said press the lock button 4 times to deactivate the ultrasonic sensors…” – DodgeJourneyForum.com

8. Incorrectly Installed Aftermarket Alarm

An incorrectly installed or faulty aftermarket alarm system is a common cause of nuisance alarms.

Aftermarket alarms are typically far more complex than any factory-installed equipment which makes them more prone to issues.

They may also have been installed by incompetent individuals.

If you are experiencing issues with an aftermarket alarm, the best thing to do is speak with a reputable auto electrician. 

“If this is an aftermarket alarm, disconnect it. Have heard nothing but trouble with those…” – Community.CarTalk.com

9. Faulty Body Control Module (BCM)

A faulty body control module can cause a wide range of issues including nuisance alarms.

  • The BCM is in charge of electrical communication from different electronic systems.
  • This includes the alarm system, lock-unlock functions, climate control etc.
  • If you have a faulty BCM you may notice other electrical glitches too
  • This can include intermittent operation of various electrical functions, such as the horn, lights, wipers and instrument cluster dials

The signals sent from the door and hood are sent to the BCM to be interpreted and it is a core part of the alarm system.

The BCM can be connected to a diagnostic scan tool which should uncover any errors or show a lack of communication with the main computer.

If in doubt, speak to your local dealer or a reputable mechanic to carry out the tests for you.

10. Damaged Wiring

Damaged electrical wiring can cause a wide range of problems, it can often be tricky to pinpoint too and you may need to have an auto electrician run some diagnostic tests.

In some instances, rodents may have chewed through an electrical wire.

We found this experience shared by an owner on DodgeJourneyForum.com:

“In the end, they found that the wires connecting to the module for the alarm were loose/not connected properly. So they fixed that. I haven’t had the problem since and I’m keeping my fingers crossed…”

11. Animals Climbing On The Vehicle

If your alarm has been set off in the middle of the night, it may have been by an animal climbing on the car.

States such as Illinois, Indiana, Iowa, Texas, Wisconsin, and Carolina have large wild raccoon populations. 

Have a look for footprints on the hood and the roof. 

If you have a CCTV system, examine the footage. These animals usually appear during the night. 

12. Not Closing Doors, Hood, or Trunk Properly

Something as simple as not properly closing the doors, hood, or trunk will inevitably trigger the alarm.

Make sure to check if you have closed every point of entry of your vehicle to avoid accidentally tripping your vehicle’s alarm. 

Alternative Suggestions

Check for Recalls or TSBs

By entering your car’s VIN number on Dodge’s recall page or the NTHSA’s Safety Issues & Recalls page you can determine whether or not there is a TSB or recall for your vehicle and if there is you’ll want to get it addressed.

A recall is issued by a vehicle manufacturer for issues that are safety-related, while a TSB covers components that may be malfunctioning but don’t compromise the safety of the vehicle.

Disconnect the Battery

Sometimes mysterious alarm problems can disappear with a simple reboot, there are no guarantees here but it’s worth a try.

Disconnect the battery for 20 seconds and this resets many of the electronics in the vehicle.

Check For Warning Messages

When the alarm occurs can you see any lights or warning messages on the instrument panel?

This can give a clue as to what’s causing the alarm e.g. ‘Hood Ajar’.

Take it to a Dodge Dealership

If needed, take your Dodge to the dealership.

Tell them you are NOT paying for a check on what the problem might be.

Ask them if they will check it for free.

Most dealerships and other places do quick/initial diagnosis for no money as they plan to make money for the repair of your vehicle.

If your unit is still under warranty then they should fix and resolve the issue for free.

How to Test the 12V Battery

How to Test the Battery:

  • Before testing, remove the surface charge from the battery, this allows for an accurate reading.
  • Simply turn on the headlights for 2 minutes then turn off.
  • Set the multimeter dial to the ’20 Volts’ setting.
  • Make sure the car is turned OFF.

The multimeter will have a red probe and a black probe.

  • The red probe is for making contact with the positive terminal.
  • The black probe is for making contact with the negative terminal.

Measure across the battery terminals.

  • The meter should display a reading, if the battery is fully charged the voltage should be between 12.2 and 12.6 volts.
  • Anything under 12V and the battery should be charged or replaced.

Related: Dodge Nitro Alarm Going Off? (12 Common Causes)

Sources

https://www.mopar.com/en-us/my-vehicle/vehicle-information.html

https://www.kbb.com/dodge/recall/

Author:

  • Growing up with a father who was a mechanic I had an appreciation for cars and motorcycles from an early age. I shared my first bike with my brother that had little more than a 40cc engine but it opened up a world of excitement for me, I was hooked. As I grew older I progressed onto bigger bikes and...

    View all posts